Gas Grill Burners: Getting to Know You

The cast brass and cast stainless steel burners have the smallest burrs — by far. This will mean less chaos in the gas flow, fewer trapped particulate matter in the burner and a cleaner burning grill. The following comparison shows how the ports are formed.

Why is port formation important? Several reasons. If the hole is punched into a sheet metal burner, it leaves a large tab inside the burner that will cause more chaos while burning.

It is more apt to hold trapped food particles and grease, and is therefore more likely to burn through. (Note the Alfresco burner photo below.)

*****************************************************

Recommended For You

Store Buildr - Tablets Galore Superstore

The Ultimate ‘Done For You’ Niche Website Store!

Nano Video Hosting and Live Streaming - 100GB

Video hosting and live streaming service, including unlimited bandwidth, True TV and VOD.

Kaptiwa Best Seller

Get this Lightning FAST Video Hosting and Marketing Software to Sell More and Deliver Faster Training for One-Time-Price

*****************************************************

Molded ports in cast burners seem like they would be a good idea, but there is considerable difficulty in making them uniform. Thus, it is quicker and less expensive to drill.

Drilled ports are the most uniform and the most precisely placed. They tend to leave a burr on the inside of the burner, which is more noticeable (oddly enough) in a sheet metal burner. Cast burners tend to have smaller burrs.

Fire Magic grill burner has drilled orifices
Notice (from the photo on our site) the lack of extensive burring, allowing for a smooth flow of gas. Cast stainless leaves few, if any, burrs when drilled. This burner has a lifetime warranty, including against rust and burn-through.

Notice the placement of the ports: on the side, safely below the ridge.

This placement will help prevent grease from dripping into the burner, minimizing the possibility of grease entering the burner.

Lynx grill burner is drilled
Notice (from the picture on our site) the lack of extensive burring, allowing for a smooth flow of gas. Cast brass is similar to cast stainless steel when drilled, leaving few, if any, burrs. This burner carries a lifetime warranty, including against rust and burn-through.

It is also interesting to note that Lynx does not offer a replacement burner for any of their grills: simply, you’ll never need one.

*****************************************************

Recommended For You

MailEngine - List Janitor Pro Yearly

Powerful email marketing system that improves your inboxing and increases your returns from email marketing

Traffic Rebirth

Traffic Rebirth

*****************************************************

Orifice placement is not as good with this burner as with the Fire Magic, but when you consider that you’ll never replace this burner, it probably doesn’t matter all that much.

Alfresco grill burner has punched orifices
Punched ports like these create substantial ledges where carbon particles and moisture can collect and foster burn-through. This burner has a limited lifetime warranty that only covers manufacturer’s defect. With this design, this burner *will* burn through, and faster than most other burners on the market.

Further, notice the placement of the ports: at 10 o’clock and 2 o’clock; if any grease were to drip onto this burner, it is almost guaranteed to enter these ports, thereby compounding the rust and burn-through issue.

DCS grill burner has drilled orifices
At least DCS drills burner ports. The burrs, however, are substantial when compared to cast stainless steel, and these will also collect particulates and moisture, which will foster burn-through.

This burner also has a limited lifetime warranty that covers manufacturer’s defects only, not rust or burn-through.

This burner has a thicker steel than the Alfresco, but it also has a serious design flaw: the ports are drilled directly on top.

If grease were to drip on this burner, it is guaranteed to enter the burner, compounding the rust and burn-through issue!

Thank you for taking the time to read our article.
**********************************************************

Interested in building a blog or auto-blog like this one ? Or just want to order one ?  Join our "Blogging Tips Tricks and Resources Skype" Group and let's chat about it. 

Join "Blogging Tips Tricks and Resources Skype" HERE

Interested in Starting your own Roku TV Channel ? Or interested in learning how to build one ? Join our "Roku TV Channel Development" Skype Group and let's chat about it. 

Join "Roku TV Channel Development" HERE

**********************************************************

If you enjoyed our content, we'd really appreciate some "love" with a share or two.

And ... Don't forget to have fun!